Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 1

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 2

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 3

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 4

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 5

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 6

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails

YBS-6133 plastic gear grease is formulated with a base oil thickened with high-grade fatty acid soap and enriched with antioxidants, anti-corrosion agents, and other additives. It contains highly efficient solid lubricants, exhibits good compatibility with plastic and rubber parts, and demonstrates outstanding noise reduction, anti-wear performance, long service life, and moderate damping within a certain low-temperature range.

This product is silicone-free and will not cause electrical contact failure. It contains special additives , providing outstanding anti-wear properties, long-lasting lubrication, and excellent resistance to oil separation.

Inquiry

Write a Review

Performance characteristics

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 7 It exhibits excellent vibration damping, noise reduction, damping, and lubrication properties over a wide temperature range.

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 9 Good water resistance, rust prevention, and corrosion resistance.

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 10 Low volatility, good oxidation resistance, and long lubrication life.

Performance characteristics

Plastic gear grease YBS-6133
Appearance	Visual inspection	White, uniform oil
Drop point ℃	ASTM D2265	Not less than 180
Working cone penetration @25℃ 0.1mm	ASTM D217	310-340
NLGI consistency	ASTM D217	1
Copper corrosion (100℃, 24h)	ASTM D4048	Qualified
Evaporation loss (100℃, 24h) %	ASTM D972	Not greater than 1.0
Oil separation of steel mesh (100℃, 24h) %	ASTM D6184	No greater than 5.0

☆ The above data are typical values for the product and do not constitute a contract.

Data for each batch of products may fluctuate within the acceptable range of Jialede's quality standards.

Application and Packaging Specifications

Custom YBS-8030 Quick-Drying Dry Film Lubricant Manufacturer YBS 6 Suitable for low-to-medium speed lubrication parts such as automotive steering switches, plastic gears, slide rails, plastic-to-plastic and plastic-to-metal components, with an operating temperature range of -25 ℃ to 150 ℃.

Custom YBS-8030 Quick-Drying Dry Film Lubricant Manufacturer YBS 6 This product is available in 5KG and 16KG packaging . For product safety handling information, please refer to the product MSDS.

*Please store in a dry place, away from other flammable materials, heat sources and direct sunlight.

slide rails

plastic gears

automotive steering switches

Low Noise Bearing Grease Supplier for Plastic Gears and Sliding Rails 16

Operating Precautions

■ Ensure gear surfaces are clean before application.
■ Do not mix with other lubricants unless compatibility is confirmed.
■ Avoid over-lubrication, especially in enclosed gear systems.
■ Use within the recommended temperature range.
■ Prevent contamination during storage and application.

How To Use

■ Clean gears and remove old lubricant before application.
■ Apply grease evenly to gear teeth and contact surfaces.
■ Use an appropriate amount to ensure full coverage without excess.
■ Apply manually or through a lubrication system.
■ Run equipment at low speed after application to ensure proper distribution.

Let's Discuss Your Needs.

Please fill out the contact form below if you would like to receive more information about our company or our product range.