Low-Temperature Bearing Grease YBS-30L Manufacture JLD 1

Low-Temperature Bearing Grease YBS-30L Manufacture JLD 2

Low-Temperature Bearing Grease YBS-30L Manufacture JLD 3

Low-Temperature Bearing Grease YBS-30L Manufacture JLD

YBS-30L premium lubricating grease is formulated with a base oil thickened with high-grade fatty acid soap and enriched with antioxidants, anti-corrosion agents, and other additives. It contains highly efficient solid lubricants, exhibits good compatibility with plastic and rubber parts, and demonstrates outstanding noise reduction, anti-wear performance, long service life, and moderate damping within a certain low-temperature range.

This product is silicone-free and will not cause electrical contact failure. It contains special additives, providing outstanding anti-wear properties, long-lasting lubrication, and excellent resistance to oil separation.

Inquiry

Write a Review

Performance characteristics

Low-Temperature Bearing Grease YBS-30L Manufacture JLD 4 Low coefficient of friction, excellent cable lubrication and load-bearing capacity;

Low-Temperature Bearing Grease YBS-30L Manufacture JLD 5 Wide operating temperature range: -40~120 degrees Celsius;

Low-Temperature Bearing Grease YBS-30L Manufacture JLD 6 Low volatility and not easily oxidized;

Low-Temperature Bearing Grease YBS-30L Manufacture JLD 8 Excellent high and low temperature stability, and extremely long service life;

Low-Temperature Bearing Grease YBS-30L Manufacture JLD 9 Excellent water and corrosion resistance, and good compatibility with the vast majority of plastics and elastomers.

Performance characteristics

Project	Typical data	Test methods
NLGI consistency level	1	ASTM D 217
Working cone penetration, 0.1mm	325	GB/T 269
Dropping point, ℃	200	GB/T3498
Water loss (79℃, 1h), % (mass fraction)	1	SH/T 0109
Wear resistance (four-ball method) wear mark diameter (mm)	0.6	ASTM D2266
Extreme pressure performance (four-ball method) sintering load PB value N	784	GB/T 12583
Evaporation loss (120℃, 22h), Wt.%	0.6	ASTM D972
Oil separation of steel mesh (100℃, 24h) /%	1	SH/T 0324
Base oil viscosity at 40℃, mm²/s	80	GB/T 265
Copper sheet corrosion, grade	1b	ASTM D4048
Corrosion resistance (52℃, 48h)	qualified	GB/T 5018

Application and Packaging Specifications

Custom YBS-8030 Quick-Drying Dry Film Lubricant Manufacturer YBS 6 It exhibits excellent vibration damping, noise reduction, damping, and lubrication performance over a wide temperature range.

Custom YBS-8030 Quick-Drying Dry Film Lubricant Manufacturer YBS 6 Excellent water resistance, rust prevention, and corrosion resistance.

Custom YBS-8030 Quick-Drying Dry Film Lubricant Manufacturer YBS 6 Low volatility, good oxidation resistance, and long lubrication life.

This product is available in 500g sizes. Packaging options include 1kg tin cans, 16kg plastic drums, and 180kg tin drums . For product safety handling information, please refer to the product MSDS.

Please store in a dry place, away from other flammable materials, heat sources and direct sunlight.

Low volatility and good antioxidant properties

Vibration reduction, noise reduction, damping

Waterproof, rustproof, and corrosion-resistant

Operating Precautions

■ Ensure gear surfaces are clean before application.
■ Do not mix with other lubricants unless compatibility is confirmed.
■ Avoid over-lubrication, especially in enclosed gear systems.
■ Use within the recommended temperature range.
■ Prevent contamination during storage and application.

How To Use

■ Clean gears and remove old lubricant before application.
■ Apply grease evenly to gear teeth and contact surfaces.
■ Use an appropriate amount to ensure full coverage without excess.
■ Apply manually or through a lubrication system.
■ Run equipment at low speed after application to ensure proper distribution.

Let's Discuss Your Needs.

Please fill out the contact form below if you would like to receive more information about our company or our product range.