loading

How to Choose the Right Electronic Fluorinated Liquid for Your Cooling System

A cooling system may be able to achieve the desired cooling temperature in a test bench setting but may have trouble during production. Maybe there is insufficient cooling capacity during cold start-up, or the fluid is lost too quickly from the reservoir because of a leak or excessive evaporation. The quality of the coolant is not always the issue; sometimes the properties of the coolant are not appropriate for the equipment.

Selecting an electronic fluorinated liquid therefore involves reviewing the entire cooling circuit before comparing the prices of different fluid grades. The best short list is determined by the following: Operating limits, fluid behavior, and the cost of system maintenance in practice.
YBS Electronic Fluorinated Liquid Products for Cooling Systems

Define What Your Cooling Circuit Actually Needs

Start with the equipment drawing and operating record. Record the minimum start-up temperature, normal supply and return temperature, maximum heat load, pump capacity, system pressure, and the amount of fluid. If there are short-duration temperature or heat-load peaks, include them as well, since a fluid that can handle a brief peak may not be suitable for continuous operation at the same temperature or load.

Then, determine if coolant comes in contact with energized parts or remains in pipes and heat exchangers. For direct-contact systems, the fluid must have proven dielectric properties and demonstrated compatibility with the electronic components it will contact. Flow, heat transfer, wetted material compatibility may be more important in an isolated cooling loop.

Lastly, determine if equipment is for single-phase circulation or controlled boiling and condensation. That decision should be based on the system design and operating requirements, not simply on which fluid has the most attractive boiling point! If it is converted to a different fluid, such as a dielectric fluid, the pump size and/or the heat exchanger size may need to be changed, and it cannot be assumed that the same pump/heat exchanger originally for water-glycol will work in the new fluid.

How to Compare Electronic Fluorinated Liquid Grades

Look Beyond the Published Boiling Point

Boiling point is only one of the limits that must be considered when selecting a suitable cooling fluid. Vapor pressure is important in systems where warm coolant is stored or circulated, particularly when leakage or vapor loss is a concern, while low-temperature viscosity matters when a pump starts after a period of inactivity. The fluid properties also vary with the system pressure.

YBS-HT170 PFPE heat-transfer fluid has a published boiling point of 170°C and is listed for applications such as circulating chillers and precision manufacturing. However, this does not mean that it is suitable for operating every cooling system near 170°C, as actual suitability depends on the system design, operating pressure, and other fluid properties.

The YBS-7300 hydrofluoroether fluid, on the other hand, has a listed boiling point of 98°C, and is being sold for cooling and certain cleaning applications. It has a different chemistry, and will have to be dealt with separately for containment, pressure and recovery. The two grades are not interchangeable with other brands of fluids.

Match Heat Removal to Available Flow

The existing piping and heat exchanger must be able to handle the equipment's heat load when using the selected coolant. Calculate specific heat, density, and viscosity for temperatures that the circuit will actually pass through. Thermal conductivity is also an important factor but is not sufficient in itself to predict the performance of a system.

Request the engineer to work out a temperature rise in the supply to return flow system at the suggested flow rate. Then verify if the pump can deliver that flow rate, taking into consideration line losses, filters, and the pressure drop across the heat exchanger. This would pick up a practical discrepancy that a positive laboratory value would fail to detect.

Check Every Material the Fluid Will Touch

Even a chemically stable fluid may not be appropriate for a specific gasket, hose, adhesive, plastic housing, or coating. Ask for information on the types of materials and how long they will be exposed to the coolant, rather than a general assumption that the coolant will be safe for electronics.

If it's a direct contact system, check the dielectric information and the way that the system will be monitored for contamination during operation. A fresh fluid sample may have different electrical properties from fluid contaminated by moisture or dirt entering the tank.

A Practical Comparison Table for Cooling Fluids

Question before ordering

Evidence needed

Why it can change the decision

Will the fluid remain in the intended phase? Boiling point, vapor pressure and operating pressure Prevents unintended boiling or vapor loss
Can the existing pump circulate it? Viscosity data and pressure-drop estimate Avoids inadequate flow at startup or load
Will it remove the required heat? Specific heat, density and system calculation Checks temperature rise at available flow
Is it safe for wetted materials? Grade-specific compatibility results Identifies swelling or material damage
Can it be maintained economically? Fill volume, recovery plan and supply terms Reveals costs beyond container price

Account for Fluid Loss, Storage, and Recovery

If the system is large and requires a significant amount of initial filling, a lot of money can be locked up in coolant. Estimate complete charge and stock, probable top-ups, and hose/equipment fluid content during servicing. If the vapor pressure is appreciable, sealing the tanks and vapor recovery could be a major operating cost.

Inquire about batching and batch identification methods, shelf life and storage directions, and whether or not the same grade can be provided for future topping. Review the environmental data provided to find out the exact chemistry, including greenhouse impact and any area of restrictions. The term “fluorinated” does not imply the product is environmentally preferable.

Approve the Fluid Using Evidence From Your System

Ask for an up-to-date technical data sheet and safety data sheet, and then compare the candidate with the equipment manufacturer's recommended fluid requirements. If a substitution is suggested, choose an acceptable procedure for cleaning or draining rather than take the risk of mixing old and new coolants.

Under representative loads, during a supervised trial, record start-up behavior, flow, pressure drop, inlet and outlet temperatures, and measurable fluid loss. Inspect seals and other wetted surfaces after exposure. Determine acceptance criteria in advance to prevent another problem from being masked by a satisfactory-looking temperature reading. If you have a number of cooling units that are identical, a test run on one will reveal some real differences before you lock in a bigger purchase. Keep the sample identity and batch number for further checks.

YBS provides various families of fluorinated liquids, but each product needs a product-specific decision to be made. Make sure that the people who will maintain the equipment later record the final grade and service procedure.

Conclusion

The selection of electronic fluorinated liquid is not made based on the highest rated temperature. It is about discovering a fluid that will circulate while transferring heat, will not leak out, and will be compatible with the materials already installed in the system.

The YBS electronic fluorinated liquid range provides candidates, but operating data and equipment approval determine the final choice. The ideal coolant is one that can be proven to function in the actual circuit and is stable after initial successful testing.

prev
How Does Electronic Fluorinated Liquid Enable Immersion Cooling for Data Centers?
recommended for you
Get in touch with us
Jialede (JLD) Lubrication Materials

Industrial Lubrication Manufacturer.

Contact Us

Contacts: Sales Department

E-mail: info@ybslube.com

Tel: +86-13192083114

WhatsApp: +86-18934578611

ADD: Building 15, No. 142, Jinghai West Road, Chang'an Town, Dongguan City, Guangdong Province, China

Social Media
Copyright © 2026 | Dongguan Jialede Lubrication Materials Co.,Ltd Sitemap
Customer service