loading

What Are the Primary Applications of PFPE Oil Across Industries?

Lubrication needs vary between a vacuum pump exposed to reactive gases, a miniature motor with narrow clearances, and a heated production chain. However, each could be improved by a fluid that resists chemical attack or which evaporates very slowly. In specific equipment, where hydrocarbon based lubricants are not able to satisfy those requirements, PFPE oil (perfluoropolyether oil) is used.

These oils are also commonly considered by buyers researching PFPE grease manufacturers. Both products can share the same fluorinated base-fluid chemistry, but oil can be delivered through a suitable feed system, whereas grease contains a thickener that helps it stay in place. 

This is best illustrated in terms of the actual use of the liquid.

Primary PFPE Oil Applications Across Industries

1. Vacuum Pumps in Semiconductor Manufacturing

Vacuum pumping systems can be exposed to reactive gases during plasma-etching and other semiconductor processes. In these types of environments, the oil-sealed pumps require a low vapor pressure oil that has the right resistance to the process chemistry. If not, maintenance and contamination issues with oil breakdown or backstreaming can occur.

The YBS-1304 PFPE vacuum pump oil is recommended for vacuum sealing and lubrication. It has been published with data on viscosity at various temperatures and evaporation-loss testing. For example, a pump operating in a corrosive etch environment may require more frequent oil monitoring than a pump in a clean laboratory environment, even if both operate at the same pressure, because the first pump is exposed to corrosive etch by-products. Dry pumps and other oil free type pumps do not require an oil fill.

YBS-1304 Perfluoropolyether Oil

2. Valves and Dynamic Seals in Chemical Processing

The valve stem or moving seal may come in contact with harsh process chemicals. It should allow unrestricted motion, and not create an undesirable change in the seal or pollute the material being processed. Very important to know the concentration and temperature of the chemical as well as the name.

The 1108 PFPE lubricating oil is recommended for use on valves, plugs, bearings and pneumatics in chemically critical environments. The published kinematic viscosity at 40°C is 510 mm²/s, which means that it is a relatively thick oil. That number can be important when evaluating if it can be delivered via a specific medium. For valves that are cycling a lot, ensure that the oil does not flow into the process stream. Seal-material compatibility and equipment manufacturer's recommendations are still a must.

3. Micro-Bearings and Precision Instruments

A thin and well controlled oil film may be sufficient for the operation of small bearings, micro-motors, and measuring instruments. Too much can lead to movement into neighboring assemblies; too little can impact start-up and movement through tight clearances.

Precision instruments, high-speed parts, electronic equipment: The precision grade 1101 PFPE oil is recommended for these applications. Its reported viscosity is 48 mm²/s at 40°C, compared with the 1108 grade's viscosity measured at the same temperature. The amount of application and component clearances must also be taken into account with the fluid's grade. To avoid excessive oil reaching nearby optical or electrical surfaces, a needle dispenser or other metered applicator might be necessary.

4. Aerospace Mechanisms and Ground Equipment

Wherever there are mechanical components exposed to PFPE fluids that may not be compatible with conventional fluids due to evaporation or chemical exposure, they can be assessed for compatibility.

Aerospace applications are one example listed in the catalog as the 1107 PFPE oil. A product page containing information about the use of the product in the aerospace industry is not an airworthiness approval. Flight-critical components must be qualified to the equipment specification, which specifies applicable outgassing, materials, and service-life tests. The approval process for ground-support equipment may be different. Condensable vapor deposits must also be assessed for vacuum-exposed hardware, or an oil's evaporation figure is insufficient to define spacecraft cleanliness.

5. Lubricated Chains in PCB Baking Ovens

In some electronics manufacturing lines, work pieces are conveyed through ovens by long length of roller chains and automated oilers. In these systems, the key is to make sure it delivers the accurate level of delivery, rather than being the most spectacular maximum-temperature system. Lubricating oils that leak or dry out too rapidly can be unable to reach the moving parts during the operating cycle.

This YBS case study describes using 1103 PFPE oil on roller chains running at approximately 80°C in a PCB baking tunnel. It provides information on the improved lubricant retention post evaluation but does not provide results for all oven designs. The operating temp reported is a relatively low 80°C, and the point was not to set a record for extreme operating temps, it was controlled oil retention, which is the issue. Feed rate & chain construction are still particular about installation.

6. Oxygen-Related Valves and Gas Equipment

Some PFPE fluids are suitable for oxygen-handling equipment because they offer greater oxidation resistance than many organic lubricants. The oxygen compatibility requirement, however, is one for safety, grade by grade, and does not allow any fluorinated oil to be used.

The 1098 PFPE oil is listed for oxygen service in the catalog. Before use, obtain the required evidence of oxygen compatibility, verify the pressure and temperature limits, and follow approved cleaning and assembly requirements. No supplier description or claim of similarity to another brand can be a substitute for formal qualification. Even a well-designed oxygen system can be ruined if cleaning residues are not approved or too much lubricant is used.

PFPE Oil Applications at a Glance

Application

Lubricated component

Main evaluation point

Semiconductor manufacturing Oil-sealed vacuum pump Vapor pressure and process-gas exposure
Chemical processing Valve and moving seal Fluid and elastomer compatibility
Precision equipment Micro-bearing or miniature motor Viscosity and oil migration
Aerospace Qualified mechanical interface Component-specific approval
PCB production Heated oven roller chain Delivery to joints and oil retention
Oxygen service Approved valve or gas component Documented oxygen compatibility

PFPE Oil vs. Grease: What PFPE Grease Manufacturers Supply

Oil and grease may share the same PFPE base fluid; however, PFPE grease contains a thickener, often PTFE, that helps it stay in place. On the other hand, equipment that is designed around an oil reservoir, wick, or dispenser might need liquid instead of grease.

Also, take care that the lubricating PFPE oil is not confused with electronic fluorinated heat-transfer liquids. Both are touted as "fluorinated fluids," and both have a function and specification, but they don't have the same one. If comparing PFPE oils with PFPE grease, remember that the oil applies to the machine design and that the grade-specific data applies.

Conclusion

PFPE oil has been proven in some vacuum pumps, chemical valves, precision mechanisms, heated chains, and some special aerospace or gas systems. In all these applications, the resistance to heat is not the only factor driving the applications but a special requirement for fluid lubrication in challenging conditions.

If you are comparing PFPE grease manufacturers and oil suppliers, first check whether your equipment requires liquid oil or grease, which grade is suitable, and what testing is needed. Consider the YBS lubricant range and select a product that matches your equipment's requirements.

prev
What Is the Role of Electronic Fluorinated Liquid in Semiconductor Manufacturing?
recommended for you
Get in touch with us
Jialede (JLD) Lubrication Materials

Industrial Lubrication Manufacturer.

Contact Us

Contacts: Sales Department

E-mail: info@ybslube.com

Tel: +86-13192083114

WhatsApp: +86-18934578611

ADD: Building 15, No. 142, Jinghai West Road, Chang'an Town, Dongguan City, Guangdong Province, China

Social Media
Copyright © 2026 | Dongguan Jialede Lubrication Materials Co.,Ltd Sitemap
Customer service